Concrete Lab Equipment

For compaction of cement concrete while casting cubes. Table top 500 x 500mm with elevated edges. Maximum Load capacity 140 kg. The variable pitch pulley arrangement permits the frequency to be varied between 2600 to 3600 RPM. The machine has fixed amplitude. The unit is provided with starter switch

Other sizes available -

• Table top size 600 x 600mm
• Table top size 1 meter x 1 meter

As per IS: 5515. Apparatus is complete with with hoppers and receiver assembly. Built on a rigid and stable frame consists of two conical hoppers, each with a hinged trap door. Trap door is operated by a quick  release mechanism to allow a free fall to the released concrete mix sample. A cylindrical mould is fitted beneath the two hoppers. Hoppers and receiver can be easily removed for cleaning.

As per IS: 1199. The instrument comprises of a slump cone with a hopper, specimen container, a transparent plastic plate attached to a graduated rod, , mounted on a vibrating table, and a tamping rod 16mm dia. x 600mm long. The vibrating table has fixed amplitude and frequency of vibration, imparted by a motor drive mechanism.

As per IS: 7320. It comprises of slump cone (Top dia 100mm, Bottom dia 200mm& Height 300mm) with handles made of mild steel sheet, a chrome plated graduated tamping rod 16mm dia x 600mm long , rounded at one end and a hexagonal base plate.

As per IS: 4031. This apparatus is suitable for making cubes of 70.6mm, for mortar strength evaluation. The mould is mounted on a vibrating platform with a frequency of 12000 ± 400 vibrations per minute To the platform are attached four matched springs. The whole assembly is operated by a revolving shaft with an eccentric mechanism. The machine is supplied complete with a time switch and a 70.6mm steel cube mould with base plate.

We are engaged in offering a array of cube moulds, which are available in different sizes and are manufactured according to international quality standards. Further, these are cube moulds can be availed by our clients in various finishing. Also, these cube moulds are corrosion resistant, long lasting and cost effective prices.

Available in sizes :

• 150 x 150 x 150mm (C.I.)
• 100 x 100 x 100mm (C.I.)
• 50 x 50 x 50mm (C.I.)
• 70.6 x 70.6 x 70.6mm (M.S.)

We are engaged in offering our valued clients a quality assured range of Cylindrical Moulds, which are extensively used for testing concrete cylinders for compressive strength tests. Additionally, these moulds are split vertically into two parts. Our clients can avail these moulds in various sizes at leading market prices.


Available in sizes :

• 150mm dia. x 300mm high
• 100mm dia. x 200mm high

Our organization is engaged in manufacturing of Beam Moulds, which are used for casting concrete specimens for flexural strength testing. Additionally, available in various customized options, these moulds are manufactured with finest quality raw materials with a base plate. We offer these Beam Moulds at leading market prices.

Available in sizes :

• 100 x 100 x 500mm
• 150 x 150 x 700mm.

Inner chamber made of S.S., outer body mild steel duly powder coated. Suitable to accommodate 6 cube moulds of 150mm. The unit is provided with digital temperature controller cum indicator and water circulation pump. Temperature range 5° above ambient to 100°C. Calibration certificate is provided for digital controller.

As per IS: 5514. Used for soundness test of cement. The apparatus consists of a small split cylinder forming a mould of 30mm internal dia. and 30mm high. On either side of the split cylinder, two parallel indicating arms with pointed ends are fixed. The mould is supplied with two glass plates and lead weight. Set of six moulds supplied in a cardboard box.

As per IS:2386 ( Part IV ). The sturdy construction consists of a base and support columns to form a rigid frame work around the quick release trigger mechanism to ensure an effective free fall of hammer during test. Supplied complete with a cylindrical cup, a metal measure 75 mm inner dia x 50 mm deep and a tamping rod. The apparatus is fitted with a blow counter.

Vicat Apparatus (Setting Time & Consistency of Cement) as per IS: 5513. The apparatus consists of initial needle, final needle, consistency plunger, conical vicat mould, glass plate. The apparatus is provided with dashpot arrangement for jerk free lowering of needles

Available with

• Vicat mould 60mm top dia, 70mm bottom dia and 40mm height
• Vicat Mould 70mm top dia, 80mm bottom dia and 40mm height

As per IS: 2386 ( Part III ). Ruggedly constructed from galvanized wire mesh, approximately 20 cm dia. x 20 cm height.

Blain Air Permeability Apparatus (Fineness Of Cement) as per IS: 5516. The apparatus is used to determine the fineness of cements, pozzolans and other powders materials. The apparatus comprises one each of – Permeability cell 12.5mm inner dia. , ‘U’ tube manometer mounted on wooden stand, Perforated metal disc, Plunger, Rubber stopper, Rubber tube and Dibutylphthalate liquid.

Sturdy load frame with chrome plated piston for rust free operation

Available in models :

• 1000kN capacity, hand operated, with one pressure gauge
• 1000kN capacity, motorized, with one pressure gauge
• 1000kN capacity, motorized, with digital display
• 2000kN capacity, hand operated, with one pressure gauge
• 2000kN capacity, motorized, with one pressure gauge
• 2000kN capacity, motorized, with three pressure gauges
• 2000kN capacity, motorized, with digital display
• 3000kN capacity, motorized, with three pressure gauges
• 3000kN capacity, motorized, with digital display

As per IS: 10070. For determination of the resistance to wear of small size aggregates and crushed rocks. The machine consists of a hollow cylinder mounted on a sturdy frame on ball bearings. A detachable shelf which extends throughout the inside length of the drum catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated at a speed of 30-33 RPM by an electric motor through a heavy duty reduction gear. Motor is suitable for operation on 440 volts, 3 phase, A.C. supply. The unit is supplied complete with a tray for collection of the material with abrasive charge.

As per IS:1237, 654. This is a double lever loading machine and the load is applied by flow of lead metal which automatically stops when the sample breaks. The sample is mounted between rollers 40mm or 12mm dia. Bearing rollers can be placed at centre distances of 150, 200 or 270mm. Complete with 20 Kg lead metal.

High pressure permeability test can be conducted on different size of specimens using different cells. Cell is provided with a top plate and funnel at the bottom having gasket seals held in position through bolts & nuts. The concrete specimens are sealed in the cell to prevent any leakage along the side walls. Each unit is provided with chamber pressure gauge of 0-20kg/cm² and test pressure gauge of 0-15kg/cm². Pressure are applied using any available pressure line at the site or  compressor. Supplied without glass bottles & compressor.   

The various models are -

• Single Cell Model for specimen size 150mm cube           
• Three Cell Model for specimen size 150mm cube             
• Single Cell Model for Specimen Size 100mm dia x 100mm high     
• Three Cell Model for Specimen Size 100mm dia x 100mm high     
• Single Cell Model for Specimen Size 150mm dia x 150mm high     
• Three Cell Model for Specimen Size 150mm dia x 150mm high

As per IS: 1199 ( for Cement Concrete ). The instrument is recommended for concrete where nominal size of coarse aggregates does not exceed 38mm. It comprises of table top of 762 mm dia,  fitted on a heavy duty Cast Iron frame. A cam action provides a free fall of 12.5 mm to the table. A conical mould of 120 mm height with base dia. of 250 mm and top dia. of 170 mm is also provided along with tamping rod 16 mm dia. x 600 mm long.

Available in models

• Hand operated with M.S. table top
• Motorised with M.S. table top
• Hand operated with Gun Metal table top
• Motorised with Gun Metal table top